Make sure DEEBOT is switched ON and 100% charged Replace with brand new batteries to confirm they are placed correctlyĭEEBOT is switched OFF or DEEBOT’s battery gets low The batteries in the Remote Control needs to be changed Remote Control timeout (efficient control range of Remote Control is 5m (16′) Side Brushes and the Main Brush as described in portion 4 Switch OFF DEEBOT, clean the Dust Bin, and turn down the robot Clean.
The robot’s stuff are tangled with dirt and debris
#Spinner blinkk teice full#
Keep DEEBOT Switched ON and on the Charging Dock to make sure it has a full battery charge to work at any time as needed Set Time Scheduling function as described in section 3 Working time differs according to floor surface type, room arrangement complexity, and the selected Cleaning ModeĭEEBOT does not clean automatically at the Predefined scheduled time When battery power gets down, DEEBOT automatically Return to Charging Mode and returns to the Charging Dock to recharge itself If the Main Brush still rotates slowly, Remove the dirt and debris tangled around the Main Brush with the given Multi-Function Cleaning ToolĭEEBOT come back to the Charging Dock before it finishes scheduled cleaning work Main Brush get stuck or the rotation speed of the Main Brush reduces Remove the dirt and debris tangled around the Side Brush Side Brush get stuck or the rotation speed of the Side Brush reduces If it is failed, manually remove the blockage and restart May DEEBOT is led with something on the floor (hair, electrical cables, drooping curtains, carpet fringe, etc.)ĭEEBOT will try in different ways to untangled itself. Keep DEEBOT on the Charging Dock to confirm it has a full charge to clean at any time as neededĭEEBOT gets into difficulty while working and stops Plugin the charging dock and make sure DEEBOT is powered on. The charging dock is unplugged When DEEBOT is powered Turn on, which causes the battery drain Make sure that DEEBOT’s charging contacts have established a connection with charging dock pins, you can remove the robot manually if you need to connect Press down and keep hold AUTO Mode Button on DEEBOT to power ONĭEEBOT failed to establish a connection with the Charging Dock If a user’s router set a 2.4G and 5G Wi-Fi at the same time, set the two frequencies for different SSID.Ĭonsidering the Wi-Fi connectivity, we should bet on this best robot vacuum for carpet suggestions that had multiple sensors to drive in the right way and adjust automatically. If it still does not work, break it down! Oh no, don’t take it seriously.Try to restart the router and the phone to connect the internet network again.Disconnect other additional user devices from the mobile Wi-Fi, mainly for Peer-to-Peer (P2P) Network downloads and online videos when connecting the robot.Do not minimize the background in the App when the network is going connect.Check if the Wi-Fi credentials are correct.Check if the phone is linked to the Wi-Fi and the Wi-Fi can communicate the internet normally.
Place the robot towards the router where the wireless signal strength is powerful.The robot only supports 2.4G Wi-Fi but does not support 5G Wi-Fi and enterprise networks. The user device is not able to connect to the mobile Wi-Fi Manually by hand Place your DEEBOT N79 on the Charging Dock, disconnect after 3 minutes charging, repeat this process 3 times then charge normally. Solution: Replace and re-activate the battery. Possible Cause:The battery is fully discharged. Your DEEBOT N79 Keep on the Charging Dock to make sure it has a full battery charge to work at any time as needed. Solution: Ensure the robot’s side Bottom Power Switch is turned ON when Plugged in the Charging Dock. Possible Cause:Maybe Charging Dock is unplugged while the robot’s Bottom Power Switch is ON, which causes battery drain. If necessary, you can remove the robot yourself to connect. Solution: Confirm that DEEBOT N79 has made a connection with the Charging Dock Pins. Keep the immediate area 2m in front of the charger and 1 m on both sides of the charger clear of objects and reflective surfaces. Place the Charging Dock on a level floor surface against the wall with the base vertical to the ground. You probably do not know, Check the facts. Possible Cause:Maybe, DEEBOT N79 did not connect to the charging dock. DEEBOT is powered goes ON when Power Indicator light glows a continuous BLUE. You have to know “l” indicates ON and “O” indicates OFF. Basic Declaration & Usage name-of-animation īackground:url(./img/lamp.png) 0 0 no-repeat īackground:url(./img/hand.Solution: Turn the robot’s Side Power Switch to the ON position.